Encyclopedia Astronautica
DC-Y



dcycu.jpg
DC-Y
Credit: NASA
American manned spacecraft. Study 1995. The ultimate goal of the Delta Clipper program, a prototype reusable single-stage to orbit, vertical takeoff/vertical landing space truck. The DC-I Delta Clipper would be the full production version.

No government sponsor could be found for the concept and the $ 5 billion development cost was never funded. If it had been funded in 1991, the first DC-Y suborbital flight was predicted for 1995, and a first orbital mission in 1997.

The Delta Clipper was envisioned as a spaceship that could take off straight up and land the same way, not gliding but under power, just like the rocket-ships in the 1950's science-fiction movies. Because of its improved engines, high-tech light-weight materials, and airline-like service procedures, the Delta Clipper could reduce the cost of getting to and from space by 90% or greater. Because it was to be certified for flight like an aircraft, it was to be able to operate from spaceports located in any state. The production Delta Clipper was expected to carry two crew members and 10 tons of cargo and/or passengers to Low Earth Orbit or 2 crew members and 5 tons of cargo/passengers to Polar Orbit. The anticipated turn-around time for the Delta Clipper was a maximum of seven days. However, a one day turnaround was hoped to be feasible.

The production model Delta Clipper was to be conical shaped, approximately 40 m high and 12 m across the base. It was to have eight or more rocket engines, providing safe return engine out capability like any airliner. The Delta Clipper was to not have wings like the Shuttle but was to use small moveable flaps to help maneuver. It was to not require strap-on external tanks or boosters.

The production Delta Clipper would enable any state in the Union to have its own spaceport. Unlike the Shuttle, the Delta Clipper wouldn't need a long runway, huge Vehicle Assembly Building, or Mission Control but only a 60 m diameter concrete pad, a maintenance hangar, and a hydrogen/oxygen fuel facility. It was to use existing global positioning satellites for navigation.

The total cost of developing the first flight certified Delta Clipper was to be comparable to or less than the development of a new commercial airliner. Total cost for the development of the DC-Y prototype program was estimated at $5.06 billion, including production of four flight vehicles. The ticket price for early versions of the Delta Clipper, if it met cost goals, could be less then the price for a round-the-world cruise on the QE2 ($40,000 to $140,000). A second generation vehicle could further reduce this cost. Once fully operational the Delta Clipper was to be as safe as flying on a typical commercial airliner. Delta Clipper was to have engine out and all altitude abort capability. Plans were to have the Delta Clipper certified by the Department of Transportation, Office of Commercial Space flight.

The Delta Clipper was to burn only hydrogen and oxygen. Its exhaust consisted primarily of pure water vapor. Therefore it was not expected to produce air pollution or disturb the ozone layer. Since the Delta Clipper launched straight up, the sonic boom would be largely restricted to the spaceport area. When landing, the Delta Clipper was to slow down to sub-sonic speed at about 70,000 feet altitude, thus minimizing the sonic boom to a barely audible level.

The eight engines for the DC-Y were to use off-the-shelf technology as much as possible. The LOX turbopump was the Fiat Avio - HM60 which was being flown on the Ariane. The Hydrogen Turbopump was from the P&W XLR- 129. The controls and health monitoring system was based on a P&W system developed for NASP. The thrust chamber assembly was based on a program run out of Marshall. It used a copper tubular chamber based on P&W IR&D. The Regenerator was to be new. The extendable nozzle was based on the existing RL-10. Engine valves were from the Fiat HM60. The engine was throttleable from 10% to 100% and used an expander cycle.

Characteristics

Crew Size: 2.

Gross mass: 470,000 kg (1,030,000 lb).
Payload: 9,000 kg (19,800 lb).
Height: 46.00 m (150.00 ft).
Span: 12.20 m (40.00 ft).
Thrust: 5,330.20 kN (1,198,277 lbf).

More... - Chronology...


Associated Countries
See also
Associated Launch Vehicles
  • DC-Y American SSTO VTOVL orbital launch vehicle. The ultimate goal of the Delta Clipper program, a prototype reusable single-stage to orbit, vertical takeoff/vertical landing space truck. The DC-I Delta Clipper would be the full production version. No government sponsor could be found for the concept and the $ 5 billion development cost was never funded. If it had been funded in 1991, the first DC-Y suborbital flight was predicted for 1995, and a first orbital mission in 1997. More...

Associated Manufacturers and Agencies
  • Douglas American manufacturer of rockets, spacecraft, and rocket engines. Boeing Huntington Beach, Huntington Beach, CA, USA. More...

Bibliography
  • "Single Stage to Orbit", Aviation Week and Space Technology, 1991-08-26, page 15..

Home - Browse - Contact
© / Conditions for Use